IP Switch with ESP32-GATEWAY

B I U S link image code list	Show page   Syntax
!Setup Setup are available via CLI (command line interface). How to access * connect micro USB cable * run terminal - for example Ctrl+Shift+M in Arduino IDE * set baudrate to 115200 and No line ending. [https://remoteqth.com/img/wiki-ip-switch-esp32gateway-20.png|noborder] CLI contains some commands for set or show information. Commands for set source device *'''m''' - Manual IP switch *'''r''' - Band decoder MK2 *'''o''' - Open Interface III Other commands, {.redka#id color: #f23f37}RED{/} is important *'''?''' - show status and help *'''w''' - set inactivity time in minutes, after them IP switch will be '''restarted (watchdog)''' ** before reboot store current output setting and restore after start ** zero value disable this watchdog *'''W''' - set inactivity time in minutes, after them IP switch will set '''all outputs to OFF''' ** if you need OFF all outputs after reboot watchdog, set smaller value than it ** zero value disable this watchdog *'''/''' - set {.redka#id color: #f23f37}encoder range{/} (2-g) for switching one from range *'''%''' - enable/disable {.redka#id color: #f23f37}group buttons{/} **'''!''' - SET group for each button separately **''':''' - List group buttons **in one group may be activate only one output **groups are free configurable **the group can be any size 2-8 buttons **there may be any buttons in the group, for example 1 and 8 **the number of groups is not limited *'''*''' - enable/disable serial debugging *'''+''' - select get Network ID sufix from eeprom or hardware BCD switch *'''#''' - set {.redka#id color: #f23f37}network ID{/} **'''Prefix''' (four high bit) in hexadecimal format (0-f) *** in standart mode prefix expanded range of network ID *** if enable Multi control, prefix disable, and use only on master device for his idetifications **'''Sufix''' (four low bit) in hexadecimal format (0-f) ***settings available if sufix get from eeprom *** in standart mode sufix use for identification *** in Multi control mode define group ID (id for all shared devices) *'''$''' - enable/disable {.redka#id color: #f23f37}Multi control{/} function (sharing up to 16 master device) *'''&''' - send broadcast packet for find control devices in local network *'''.''' - if enable Multi control, show list detected IP switch by ID prefix *'''@''' - restart IP switch !! For controlled from Manual IP switch * Upload firmware by previous steps * Set encoder range via CLI with command '''n''' * Set source via CLI or web interface to '''m''' * Set network ID prefix same on both devices via CLI in range 0-7 * Select Network ID sufix same on both devices with BCD switch in range '''ID 0-7'''{br}[https://remoteqth.com/img/wiki-ip-switch-esp32gateway-bcd-switch.jpg|noborder] * Connect to same local network with DHCP as Manual IP switch * After power up both devices, is automaticaly pair !!Web status page [https://remoteqth.com/img/wiki-ip-switch-esp32gateway-19.png|noborder] * Show all outputs status * Parameter of WiFi or ethrnet IP connect * Firmware version * Device uptime * How source controled his * {.redka#id color: #f23f37}Notice{/} - show this page can extend reaction latency IP switch !!How IP addres got the device from the DHCP server? * show in serial terminal after reboot, or send ? character * or find some [network scanner|https://play.google.com/store/apps/details?id=com.overlook.android.fing&hl=en_GB] !! Telnet access with KEY * Download and install [PuTTY|https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html] * In menu Terminal preset CR/LF and line discipline by picture[https://remoteqth.com/img/wiki-ip-switch-esp32gateway-22.png|noborder] * In main menu Session select or set the following values [https://remoteqth.com/img/wiki-ip-switch-esp32gateway-23.png|noborder] ** select '''Telnet''' ** port '''23''' ** write '''IP address''' ** Sessions may be saved for next time ** for connect press '''Open''' * Login confirm with press '''y''' * Now answer four times the question of what character is on random selected position, '''in your key''' ** you either get the key together with the IP-switch, or paste it into the source code{{const char* key="yWW3aaxjXua4wcoXUjkkOiAwChRwaUakVIfAUmmHV4ylwIXvN6Ucy3oH25T5ZzNYQ2r0L4s42tZIJT9XIgt9VVYxnDWtM7AVN6D8";}}[https://remoteqth.com/img/wiki-ip-switch-esp32gateway-24.png|noborder] ** if you enter wrong three times, login will be blocked for next ten minutes * After login your IP address store to EEPROM and next key will be required '''only if change your IP''' address[https://remoteqth.com/img/wiki-ip-switch-esp32gateway-25.png|noborder] * for '''Logout''' press '''q''' !! Secure remote manage Configuration available via serial CLI (command line interface). This interface can be safely accessed to the Internet and encrypted connections to manage all features [https://remoteqth.com/img/wiki-manual-ipsw-07.png|noborder] What you need * any version Raspberry PI * microSD card with [Raspbian Lite|https://www.raspberrypi.org/downloads/raspbian/] * micro USB cable * 5V power adapter with micro usb cable * ethernet connection * for first start HDMI monitor and USB keyboard How to start * after first boot login to serial console with default login '''pi''' and password '''raspberry''' * run command and '''enable [SSH|https://www.raspberrypi.org/documentation/remote-access/ssh/]'''{{sudo raspi-config}} * run command and write down the shown '''IP address'''{{ip a}} * you can disconnect HDMI monitor and USB keyboard * connect to Raspberry PI from any other PC ** [windows|https://www.raspberrypi.org/documentation/remote-access/ssh/windows.md] ** [Linux|https://www.raspberrypi.org/documentation/remote-access/ssh/unix.md] ** [iOS|https://www.raspberrypi.org/documentation/remote-access/ssh/ios.md] * update system with run command{{sudo apt-get update && sudo apt-get upgrade}} * install screen fith command {{sudo apt-get install screen}} * run '''screen'''{{screen /dev/ttyUSB0 115200}} * now after pres any key show status information and you can '''configure via CLI'''[https://remoteqth.com/img/wiki-manual-ipsw-cli.png|noborder] * close screen with '''CTRL+A K''' and confirm '''y''' * disconnect from Raspberry PI use command {{exit}} [<-- Order page|https://remoteqth.com/order.php#ip-sw-mk2] [<-- Web|https://remoteqth.com/ip-switch-mk2.php] [<-- Control box|Manual IP switch II]
Password Summary of changes